65 bombas de alimentación de filtro prensa zjw
Bombas de lodo centrífugas horizontales en voladizo / bombas de lodo revestidas de caucho / bombas de lodo R55 / bombas de lodo de sello de glándula / bombas de lodo de sello centrífugo / bombas de lodo de caucho resistentes al desgaste / bombas de lodo intercambiables / bombas de lodo de lavado de carbón / bombas de lodo de manipulación de arena y grava / lodos de manipulación de efluentes bombas / bombas de proceso de flotación de minerales / bombas de lavado de carbón / bombas de alimentación
La bomba de alimentación de filtro prensa de la serie Naipu® NP-ZJW acepta un diseño hidráulico único y un modo de instalación del
impulsor, asegúrese de que su curva de rendimiento de la bomba sea más empinada que las bombas normales, es más adecuado para usar en el
La alimentación del filtro prensa varía según los cambios de la resistencia para realizar la gran capacidad,
alimentación a baja presión y filtro de alta presión y baja capacidad.La bomba es ampliamente utilizada en la lavadora de carbón,
protección del medio ambiente, fábrica de aluminio, planta de fundición, etc.
Dibujo de construcción
El diagrama de estructura de la bomba de alimentación.
1.Voluta bifásica 2. Impulsor bifásico
3.Voluta monofásica 4.Placa trasera
5.Sala de alimentación 6.Arbusto de ubicación
7.Expeller 8.Placa de cubierta del expulsor
9.Cuerpo de descompresión 10. Impulsor monofásico
11.Barra de amarre 12.Manguito del eje
13.Placa de cubierta 14.Anillo de desmontaje
15.Placa de retención de agua 16.
17.Eje 18.Manguito espaciador de cojinete
19.Cubierta de cojinete 20.Marco
21 Tubo doblado
TABLA DE SELECCIÓN DE BOMBA NP-ZJW
PARÁMETROS DE RENDIMIENTO DE LA BOMBA DE ALIMENTACIÓN NP-ZJW
Descripciones de productos:
Posibles fallas y liquidaciones.
Faults
|
Reason
|
Settlement
|
1.Pump fails to discharge any water,The hand of pressure gauge beat violently
|
1.Suction pipe don`t have enough water.
2.Suction pipe blocked or the valve is locked.
|
1. Inject enough water
2.unlock the inlet valve,clear the blocks
3.Exclude the air leakage
|
2.The pump can`t discharge water,the hand of vacuum meter beat heavily.
|
1.The inlet valve is unlocked or silted up.
2.The resistance of suction pipe is too big or silted up.
3.The height of suction is too high.
|
1.Unlock the valve or desilting
2.improve the design of suction pipe or desilt
3.Lower the height of the installation.
|
3.The pump can`t discharge water,pressure gauge shows heavy pressure.
|
1.The resistance of the discharge pipe is too big.
2.The impeller blocked
3.The speed is slow.
|
1.Check and adjust the outlet pipe.
2.Clear the impeller
3. Improve the speed.
|
4.The pump doesn`t rotate
|
The volute is silted up by the blocks.
|
Clear the blocks
|
5.The capacity is not enough
|
1.The blocks of the impeller or the inlet or outlet pipe.
2.The abrasion of the impeller is heavily.
3.The speed is low to normal
4.Pump is installed unreasonably or the leakage of the inlet pipe.
5.The transporting height is too high,the loss of the resistance of the inside pipe are too big.
6.The inlet valve not open enough or blocked
7.The packing seal leaks
|
1.Clear the impeller or pipe.
2.Change the impeller
3.Adjust the speed
4.Install again or stop leaking.
5.Decrease the height of the transport or reduce the resistance.
6.Unlock the inlet valve
7.Compress the packing tightly
|
6.The motor of the pump is overloaded
|
1.The head of the pump exceeds the head of the working condition.
2.Not consider the slurry density when selecting the pump.
3.The packing press tightly
|
1.Turn down the outlet valve,cut the impeller or lower the speed.
2.Select the motor again.
3.Adjust the the screw of the packing gland
|
7.Abnormal sound in the pump, and no water out
|
1.The resistance of the inlet pipe is too big.
2.The height of the suction is too high.
3.Cavitation occurred
4.there is air in the inlet
5.The temperature of the liquid is too high
|
1.Clear the suction pipe and sluice valve.
2.Lower the height of the suction
3.Adjust the water valve and let the pump operate in the defined limits.
4.Block the leakage.
5.Lowering the liquid temperature.
|
8.pump vibrates
|
1.pump cavitate
2.The block of the impeller single vane
3.The no concentricity between the pump shaft and motor shaft
4.Fasteners or foundation loose
|
1.Adjust the water valve ,lower the height of the installation,reduce the resistance of the inlet.
2.Clear the impeller
3.Alignment again
4.Fasten the screw,and reinforce the foundation.
|
9.Bearing is overheat
|
1.lock the cooling water
2.lubrication is not good.
3.the lubrication oil is not clear
4.the wrong direction of the thrust bearing.
5.there is something wrong with the bearing.
|
1.Open the cooling water
2.Adjust the oil quantity
3.Clear the shaft,change oil
4.According to the inlet pressure,adjust the direction of the thrust bearing.
5.Change the bearing
|
10.Packing short life
|
The material of packing is not good
|
Change the packing
|
11.pump leak oil
|
1.High oil level
2.The rubber parts invalid
3.Assembly problem
|
1.Lower the oil level
2.Change rubber spares
3.Adjust the assembly
|
12 Pump head leaking
|
1.The rubber parts not press well
|
Assembly again or press tightly
|
PREGUNTAS MÁS FRECUENTES:
Q1. ¿Eres una fábrica fabricante?
Sí, somos la fábrica de fabricación directa y tenemos más de 10 años de experiencia en esta área.
Q2.¿Tienes productos en stock para vender?
Algunos los tenemos en stock, pero otros no. Dado que siempre producimos estos productos de acuerdo con los requisitos de los clientes.
Q3.¿Qué ventajas tiene?
R: Somos fabricantes directos y el precio es competitivo.
B: Nuestro ingeniero tiene mucha experiencia en esta área, y podemos brindarle servicio OEM.
C: Somos una fábrica y podemos organizar el cronograma de producción para una entrega puntual.
Detalles de contacto:
Bomba Co., Ltd. de Shijiazhuang Naipu
Agregar: No 368 Xinshi North Road, Zona de desarrollo de la industria de alta tecnología de Shijiazhuang, Hebei, China, 050091.
Tel: 0086-311-897162903
Fax: 0086-311-87162902
Persona de contacto: Karen Tan
Skype: karen_naipump